Transparent Exterior Stain + Sealer

  • Product
  • Colors
  • Formula Guides
  • How To
  • Product Information
Duckback Water-Based Transparent Exterior Stain+Sealer is ideal for all new or reconditioned wood surfaces that are in excellent condition.  The transparent formula penetrates into the surface providing a splash of color to highlight the natural texture and beauty of wood.

Performance

  • Sheds water after just 4 hours
  • Lost lasting color resists fading
  • Blocks UV rays to slow graying and decay

Features

  • Creates a mold-and-mildew resistant finish
  • Low temperature application down to 35 degrees F
  • 4-year guarantee on decks, 6 years on fences and siding

Category

Transparent

Colors

Transparent

Important Note: Computer screens and printers vary in how colors are displayed, so the samples shown on this page may vary slightly in color, sheen or finish from actual product and individual results. Always test a small area and let coating dry to ensure color satisfaction before coating entire area.

Formula Guides

DO NOT TINT. Product to be used as pre-packaged color ONLY.

How To

USES:

New or reconditioned wood decks, porches, outdoor furniture, steps, railings, fences, gazebos and siding.

SURFACE PREPARATION:

In order to be effective, a stain must be able to penetrate. Be sure surface is free of all dirt, mildew stains, loose wood fibers, peeling coatings and other foreign matter.  Surfaces must be sound and may be dry or damp. If damp, the wood should be free of puddles and not feel wet. Prepare previously stained or weathered surfaces by cleaning with an exterior wood cleaner. On untreated weathered surfaces, it is best to pressure wash, but at minimum, scrubbing with a stiff bristle brush and wood brightener, then rinsing with a garden hose should be done to completely remove all loose or gray wood fibers. If removing additional loose wood fibers is necessary, sanding with 60 or 80 grit paper may be required. WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment, such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

PRODUCT PREPARATION:

Product should be shaken or stirred before and during application. When using more than one container of product, intermix all containers together and stir well to ensure color consistency.

APPLICATION METHODS:

Product may be brushed, rolled or sprayed using nylon or polyester brushes, high-quality roller, stain paid or professional spray equipment. If sprayed, use the lowest possible pressure needed for a reasonable spray pattern. Back-brushing is recommended when rolling or spraying, working the product smoothly and evenly into the wood.  This will decrease the possibility of pools or puddles on the surface and ensure a properly penetrated finish.

APPLICATION:

The appearance of the finish will vary depending on the porosity and color of the wood surface.  Always test a small area first for color satisfaction before coating entire project.  Apply in small sections at a time (1-3 boards), start from one edge of the board and work end-to end.  Utilize natural break points during application to avoid any lap marks.

NUMBER OF COATS:

One-coat application is recommended.  If a second coat is desired, allow 2-4 hours dry time before applying.

APPLICATION TEMPERATURE:

35° F.–95° F. Do not apply if wood surface is hot to touch or when air or surface temperature is below 35°F or if temperature is expected to fall below 35°F for 24 hours after application.  Can be applied to both damp and dry wood. Do not apply if rain is expected within 4 hours after application.

DRY TIME @ 77° F:

4 hours to touch, 24 hours for return to service; depending on weather conditions.

coverage:

On smooth Surfaces: 300-400 sq. ft./gal.; On rough surfaces: 150–250 sq. ft./gal.

CLEAN UP:

Clean supplies and equipment with warm, soapy water. Do not freeze. Keep container closed when not in use. Do not transfer contents to other containers for storage or disposal. In case of spills, absorb with inert material such as sand or kitty litter. Dispose of empty container or unused portion in accordance with local, state and federal regulations.

Product Information

Product Number UPC Size PDS Document SDS Document Country
DBWB81000-16 740755000695 1 GAL USA
DBWB81010-16 740755000701 1 GAL USA
DBWB81020-16 740755000718 1 GAL USA
DBWB81030-16 740755000725 1 GAL USA
BCWB81000-16 740755000848 1 GAL Canada
BCWB81010-16 740755000855 1 GAL Canada
BCWB81020-16 740755000862 1 GAL Canada
BCWB81030-16 740755000879 1 GAL Canada