For wood decks - fences - siding - shake - outdoor furniture - most exterior wood
Superdeck® DFS Clear UVB
is a high-quality, clear wood stain and sealer that contains UV blockers to protect the wood from the sun's harmful rays which cause he wood to gray prematurely and breakdown.
Protects & beautifies: DFS Stain & Sealer Clear UVB is available in a tintable, natural tone. DFS's natural tone finish will highlight the wood's
grain pattern and texture, while giving a translucent and lustrous sheen.
Long-lasting color & UV protection: DFS Stain
& Sealer uses an advanced waterborne alkyd dispersion
technology which faciltates the deepest
penetration into wood surfaces. It contains high quality
UV blockers to inhibit damage caused by the sun.
Fights water damage: DFS tests exceed the industry-standard test ASTM D-4446 for
waterproofing wood, and offers long-term
water beading. In addition, DFS contains a highly-effective mildewcide to inhibit the
growth of mildew on the stained/sealed surface.
One-coat coverage: One coat of DFS Stain & Sealer is recommended for very smooth dense wood surfaces. Two coats are recommended for rough sawn or very proous wood surfaces.
Satisfaction guaranteed: We guarantee your satisfaction with the performance of Superdeck products. See product label for full details.
Trust the brand that is the professional choice -- Superdeck!
Color Samples
Superdeck DFS Clear UVB is available in a clear/natural wood tone and is tintable to
an additional three (3) shades that highlight the wood-grain pattern and
texture, giving a translucent and lustrous sheen.
Clear
Honey Gold Tint
Cedar Tint
Redwood Tint
Note: These are the best computer representations of product colors, the wood type used greatly influences the final color of stains and finishes. For best results, always obtain a sample, test a small area and let coating dry to ensure color satisfaction before making your final color selection.
SURFACE PREPARATION: DO NOT APPLY OVER SEALED SURFACES. All surfaces must be clean and free from dirt,
mildew, soot, dust, and other foreign matter. Remove previous oxidized stains and sealers
with Superdeck Wood Cleaner. New wood that has not been kiln dried must be
allowed to season before applying product. New wood may be clean enough to directly apply
stain. If not, or if wood has mill
glaze, clean redwood and cedar surfaces with Superdeck Wood
Brightener; clean pressure treated wood surfaces with Wood Cleaner. Weathered wood should be cleaned with Wood
Cleaner and rinsed. For redwood and cedar,
follow with Wood Brightener to remove tannin stains and brighten wood to its
original color.
TINTING: May use up to 4 ounces of colorant per gallon.
PRODUCT PREPARATION: Product should be stirred from bottom of container before and during
application. Shaking will create excess
air in product.If shaken, allow air to
escape before application. When using
more than one container of product, intermix all product and stir well to
ensure color consistency.
THINNING: None required.
APPLICATION METHODS: Apply product by brush, sprayer, roller, or pad applicator. Back rolling is suggested when spraying,
working the product smoothly and evenly into the wood. This will decrease the possibility of pools
and puddles on the surface and ensure a proper dry time and appearance of
finish.
APPLICATION: Proper application is essential in order to accomplish the full
benefits of product appearance and performance. DIFFERENT WOOD SPECIES, TEXTURES, AND NATURAL
COLOR WILL AFFECT FINISHED SHADE. ALWAYS
TEST A SMALL AREA BEFORE DOING ENTIRE JOB. When spraying, saturate surface leaving a wet
sheen. Then back brush or roll in a
smooth even coat. Maintain a wet edge
and apply product in entire board lengths to avoid lapping. Apply only as much product as the wood will
absorb. Do not allow product to pool or
puddle on surface. Thoroughly seal the
porous ends of all boards with several coats of product.
APPLICATION TEMPERATURE: 50ºF. - 90ºF. Do not apply if
wood surface is hot to touch or if rain is likely to occur.
NUMBER OF COATS: Apply only as much product as the wood will absorb. One coat is recommended for very smooth dense
wood surfaces. Two coats are recommended
for rough sawn or very porous wood surfaces.
DRY TIME @ 77º F: 1 hour to touch, 2-4 hours to re-coat, 24 hours for foot traffic. Dry time can be affected by species of wood,
porosity of wood, wood moisture content, and weather conditions.
You can find Duckback Products throughout the United States and Canada at independent hardware stores, paint dealers and other retailers who are committed to quality product lines and excellent customer service.
Our dealers can provide you with advice to assist you with color choices, how-to tips and professional assistance.
For information and expert advice about our full product line please call 1-800-825-5382, Monday-Friday, 7am-5pm (PST), or email our customer service representatives at: customerservice@superdeck.com
Internet Order Option:
If you would like to place an order TODAY for shipment to your home or business, visit one of our e-tailing partners.
Authorized DUCKBACK PRODUCTS internet suppliers that sell paint/stain products online. Click on the image for a link to the website.
